Sandbox:Sloth

Edits to directions

Getting Started

• Note where zip file gets extracted - this will later be called the "Sloth Directory" (full name: DIY 4-DOF Robot Kit - Sloth).

Install Arduino IDE

• No changes

Install the Driver

• The Driver folder is in the Sloth Directory, wherever you installed that.
• Double-click the PL2303_Prolific_DriverInstaller_v1180B link to bring up 7zip
• Click the extract icon
• Take note of where the zip file gets extracted - this will be called the "Driver Directory" - it is by default the Driver folder in the Sloth Directory
• Double-click the PL2303_DriverInstaller_v1180_20170406' file to run the installer; accept any defaults during installation

Add libraries

• First run Arduino by either typing Arduino into Cortana and clicking the resulting app or by going into the Windows menu and selecting Arduino
• Follow the instructions in the booklet
• Note you will be warned if the library has already been installed - this doesn't cause problems.

Test for Servos and Ultrasonic Module

• Note: For the control board, if you look at the bottom figure on p. 9 where the USB cable is up and the power cable is left, there are several groups of three pins each on the right side of the board.
  • The first pin (left-most pin) in each group is the signal pin.
  • The middle pin is the VCC, or high voltage, pin
  • The last pin (right-most pin) is the GND, or ground, pin
  • The top group of three is channel 15 while the bottom is channel 2

1. Servo test
   1. Physical test
      • Preparing the servo means using the small screw from the servo connections bag to attach the 1-sided horn to the servo.
   2. Software test
      • Test code is in the Sloth Directory under Code/Test_Robot
      • The brown wire on the servo connection will be closes to the edge of the control board; the yellow wire will be closes to the nano; in the figure on p. 11 of the booklet, the yellow wires are to the left and the brown wires are to the right.
      • From the perspective of figure on p. 11 of the booket, Pin12 is the fourth header from the top. There will be three empty headers, followed by pins 12 through 9, followed by 7 empty headers.
      • The power switch on the driver board should be in the position furthest away from the battery connection. Then the instructions say "press the power button," they really mean flip the switch on the control board.
      • Note that the servos may not be accurately by sweeping through 180 degrees
      • When you are done with the test, you will want to turn the servos off; to do that:
        • In Arduino, go to File->Examples->01.Basics->BareMinimum
        • Upload that sketch; once finished, the servos should stop moving.
2. Ultrasonic test
   • Typo: on the top of p. 12 in the first line, it should say that TRIGGER_PIN is **4** and ECHO_PIN is **3**
   • In connecting the sensor to the board, from the perspective of the figure on p. 12 :
     • Black wire is GND -- this will be the top right pin of the control board (GND for channel 2)
     • Brown wire is VCC -- this will be the pin just below that (VCC for channel 2
     • Red wire is Echo -- this will be the bottom pin one column left of brown and black (signal for channel 3)
     • White wire is Trig -- this will be the bottom pin one column to the left of red (signal for channel 4)

Contents of Box

• Instruction booklet
• Compliance and safety notice
• Structural parts:
  • Bottom plate
  • Top plate
  • Feet (2)
  • Motor chassis (2)
  • Motor frame (2)
• Fasteners:
  • 1.5*5 screw (10)
  • 1.4*8 screw (6)
  • 2*8 screw (12)
  • 3*5 screw (18)
  • 3*8 countersunk screw (8)
  • 1.4 nut (6)
  • 2 nut (12)
  • 3 self-locking nut (8)
  • 3*8 standoff (4)
  • 3*25 standoff (4)
• Electrical:
  • servo (4)
  • ping (1)
  • nano board (1)
  • expansion board (1)
  • velcro tape (1)
  • mini usb cable (1)
  • 9V battery connection (1)
  • 4-pin cable (1)
  • Phillips screwdriver
  • Socket wrench (1)
• Included, not explicitly listed in booklet:
  • Servo connectors (1, 2, and 4 sided horn) (4)
  • Screws with servo connector (sm, med, lrg) (4)
• Not included
  • 9V battery